Our Products

Elevator supplier

Fire-rated Roller Shutters

Teckentrup has offered tried and tested fire protection for many years. Today, the continuously extended range of fire doors includes a wide variety of steel fire doors for various industrial, trade and commercial requirements. According to the specified building situations or the individual demands, the various door systems are the perfect solution. State-of-the-art drive and control systems guarantee simple and safe door operation with automatic closing in case of a fire or powercut.  

First class materials and excellent workmanship guarantee quality, reliability and long service life. Teckentrup fire doors are tested in accordance with DIN 4102.

  •   Fire resistances EW 30, 45, 60, 90 - C2 (DP1)
  •   Tested according to STN EN 1634-1
  •   Classification according to STN EN 13501-2+A1
  •   Classification according to STN EN 15269-10
  •   Fire protection closure according to STN EN 14600
  •   Classification according to ČSN EN 13501-2+A1
  •   Classification according to ČSN EN 15269-10
  •   Classification according to CSN 73 0810, construction type DP1
  •   Self-closing according to EN 12605 (C2 = 10,000 cycles).
  •   Shutters conform to EN 13241-1

The shutters are designed to be installed indoors, serving as fire doors separating different areas. If the shutter is to be incorporated into the building envelope, the door must be fully protected against weather conditions, e.g. via shelters, vestibules, etc., as the characteristics regarding water-tightness, resistance to wind, heat transfer coefficient and air permeability were determined as design classification 0.

Door sizes:
Shutter sizes:
EW 30, 45, 60, 90
Width: 2 to 5.7 m
Height: 2.51 to 5.7 m

Vertical guide rails must be mounted in a fixed support structure with a minimum density of 613 kg/m3 and a minimum wall thickness of 250 mm using M10 threaded rods with maximum 750 mm spacing.

The supporting brackets must be mounted in a fixed supporting structure with a minimum density of 1,200 kg/m3 and a minimum wall thick-ness of 250 mm using threaded rods and FISCHER chemical anchors or mechanical fasteners. 

Steel "U" profiles between the lintel and the plates are to be fastened using M10 threaded rods at intervals of 800-860 mm.
The vertical guide rails are to be mounted under the cylinder onto a reinforced steel profile measuring 80 x 80 x 3 mm, coated with a layer of PROMATECT H sheeting.

Surface:
Steel plates coated with galvanised steel. Optional RAL finish (single or double) + anti-wear stainless steel plates.

Shutter curtain:
These consist of plates which are connected together with a special locking function.

Profiles:
Galvanised steel thickness of 1 mm with mineral wool infil

Lower finishing profile:
A steel "C" profile is used to place the last profile onto the non-flammable Sico silicone profile.

Drives and control units:
Direct drive with integrated facilities related to the roller shutter.

Version 1 (standard):
TAR type electrical drive (socket) 400 V, 50 Hz, 60% ED, IP54, emergency release crank. Operating temperature range: -20°C to +60°C.
The CS 310 control unit emits pulses via digital limit switches, IP 65, 24 V, and protection of lower edge by opto-sensors, CEE-plug 16A/5-pin. Operating temperature range: -10°C to +45 °C.

Version 2  (Subject to surcharge):
FDF type electrical drive type (socket) 400 V, 60% ED, IP 54 incl. 24 V DC motor for closing the shutter in case of power failure. Operating temperature range: -20°C to +60°C.

The FS 345 control unit emits pulses based on the CS 300FS control unit via mechanical limit switches. The FS 345 control unit with a backup battery, charger, sound signalling, and protection of lower edge by opto-sensors, CEE-plug 16A/5-pin. 

IMPORTANT NOTICE! According to the manufacturer, the backup battery must be tested for functionality at least every four days!

Our Suppliers

Contact Details

Contact Person Mr. Prasoon M.P
Email prasoon@gglsbahrain.com
Mobile Number 36460009